13 Things About Fiat Panda Key Fob Replacement You May Not Have Known

Reasons Your fiat car key cutting 500 Key Fob Won’t Work

A key fob from fiat key duplication 500 is a great way to unlock the doors and start the car. There are many reasons why the key fob might stop working. This could be due to a dead coin-battery, water damage, issues with the receiver module, and interference.

This listing is for a NEW replacement fiat stilo key Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths for automotive locksmiths). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common cause of your 500 key fob being inoperative. Modern key fobs have a limited operating range, and should be within some feet of the vehicle in order to function. If you’re far from your vehicle and you hit the keyfob, it will not respond and display the message “Key Fob Not Detected”.

If this occurs then replace the battery for your coin-cell (Part Number CR2032) by a new one of a trusted brand like Panasonic Duracell or Energizer. They are available at your local hardware store or on the internet.

You can test the battery in the coin-cell by pressing the buttons while you are standing close to your fiat 500x key fob 500. The car should flash its parking lights, and the key fob will operate the lock and unlock switches.

If your fob’s key isn’t working even after replacing the battery, there could be water damage that is preventing it from communicating with the module in your vehicle. Water damage can happen in a number of ways, ranging from the slightest splash to submerging the fob into salt water at the beach. If you suspect that your fob has been exposed to water, place it in a rice bag to draw out the moisture. If this does not work, you’ll have to get your fob replaced by an auto locksmith or dealer.

Water Damage

While the fob comes with rubber seals to keep water from the chip’s electronic circuit and out of the ocean or washing it in a machine can cause water damage. Saltwater poses a particular risk to the circuit board of the fob that can cause it to short out and eventually end up dying. It’s not a good thing to submerge the fob in water however, don’t give it up if you accidentally drop it in water or fail to remove it from your pocket.

First take the battery off the fob. Before replacing the battery, clean the electronic chip using isopropyl or a similar product. Check the fob to check if it’s functioning. If the key still doesn’t function, it may need to be programmed again. This is usually done by an auto locksmith or dealer.

If your key is a bit older and has not been programmed to work with your vehicle, you will need to replace it completely. A professional automotive locksmith can do this job. The locksmith must cut the key to match the ignition in your vehicle. The locksmith will also need to program your fob into the car’s system. This is an affordable and quick procedure that can be completed the same day.

Receiver Module Issues

The 500 key fob could stop working because it is out of range. The remote has a maximum range of 30 feet, which means when you’re too far from your car, it won’t respond to your commands. This can be easily fixed by moving closer to your vehicle until it begins responding.

If you’ve replaced your coin battery (commonly known as”button” or “button” or “watch”) and the fob won’t work It could be because of an internal circuit board problem. In most cases, reprogramming the fob will fix the issue. You can find instructions on how do I get a spare key for my fiat 500 to do this for the majority of automobiles by searching YouTube or looking through the owner’s manual.

It is possible to replace the metal retaining clips that hold the battery of your coin in place. If they lose tension it can prevent the coin battery from sitting properly, and this will result in the malfunction of your remote.

In rare instances, the fob may become disconnected from your vehicle because of software or hardware issues. This could be a huge headache, but you can usually fix it by visiting an auto locksmith to have them reprogram your fob for you. In some cases it is possible that the software will require reinstallation in your body control modules.

Interference

Interference can also cause the key fob to not be able to receive or transmit a signal. This could happen when the keyfob is located in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons the fiat key fobs fob could not function may be a lack of connection to the buttons, damage to the internal chip or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to solve the issue (e.g. You might have a damaged 500 receiver module if you’ve tried replacing the battery, reprogramming, or using a spare key fob. The receiver module, located under the dashboard, detects radio frequency signals from your key fob. It transforms the signals into electronic commands that are then read by the vehicle.

Fortunately, there’s an easy way to reset all of the on-board systems in your 500, including the key fob. Disconnect the 12 volt battery for about 15 minutes, by taking off the negative cable first then the positive cable. Then, reconnect the battery. This will get rid of any remaining electricity and restart the car’s computers. This could help get your key fob working again. If the issue persists you should seek out an experienced technician. They will be able to identify the root of any issues.